Omega Double Groove Aluminum Heat Diffuser Plates

Omega Double Groove Aluminum Heat Diffuser Plates

Omega Double Groove Aluminum Heat Diffuser Plates are formed aluminum plates specifically designed to pro- vide excellent heat transfer between radiant heating pipes and floors or other surfaces. They may also be used to transfer heat to various other mechanically secure surfaces in a wall or ceiling installation. HWALU heat transfer plates are a critical component of a properly designed radiant system increasing the efficiency and the reaction time of the system.

SHARE

Product Description

Omega Double Groove Aluminum Heat Diffuser Plates Video

HWALU Omega Double Groove Aluminum Heat Diffuser Plates

  1. Increases heat transfer by over 30%
  2. C-Channel design for better tubing contact and holding tubes in place
  3. Precise thickness to optimize efficiency - thicker than the other guys!
  4. Lower water temperatures
  5. Lower heating bills
  6. Great for retrofits and new construction


HWALU Omega Double Groove Aluminum Heat Diffuser Plates are formed aluminum plates specifically designed to pro- vide excellent heat transfer between radiant heating pipes and floors or other surfaces. 

Transfer plates are typically used when installing radiant tubing under existing floorsorin new installations with wood or other floor materials to be placed on top of the floor base. They may also be used to transfer heat to various other mechanically secure surfaces in a wall or ceiling installation.

Omega Double Groove Aluminum Heat Diffuser Plates are a critical component of a properly designed radiant system increasing the efficiency and the reaction time of the system.

Good radiant heating is done at low water temperatures and in the case of staple-up, that means with plates.

without heat transfer plates

without heat transfer plates

without heat transfer plates

Staple up without heat transfer plates. These system will run lower than suspend tube system but hotter than plate type system due to less conductive surface.

using aluminium heat transfer plates

using aluminium heat transfer plates

using aluminium heat transfer plates

Staple up with heat transfer plates. These system will run at a lower temperature than to the addition of aluminum fins which extend the contact surface area.

Single Groove - Heat Transfer PlatesDouble Groove - Heat Transfer Plates
Material : 26 gauge stamped aluminum sheet
Dimensions : 5” x 24” (127mm x 609.6mm)
Pipe sizes : 3/8”, 1/2” & 5/8”
Material : 26 gauge stamped aluminum sheet
Dimensions : 13” x 24” (330.2mm x 609.6mm)
Pipe sizes : 3/8”, 1/2” & 5/8”

Why?

1) The tubing will last longer.
2) Lower temperatures means less heat loss through the boiler, primary piping and tubing.
3) Fewer expansion and contraction noises.

The use of transfer plates in under floor heating is (in my opinion)the only way to go.
If you just put in more tubing per square foot your still relying on convection rather than conduction. The plates are designed to transfer the heat across the entire surface. With just the tubing, your heating the air space and trying to heat your living space via the hotter air under your flooring. Although the tubing is in direct contact with the floor, your not going to be able to get more than 8 inches on center with 1/2. Unless you plan on running several tubes down one bay, thus increasing your costs on manifolds ect. The btu's that are distributed with the plates and astro foil 5/8 of an inch under the plates yeilds 46 btu's per square foot.


The following flooring types may be installed above this type of system:

i. Nail-down solid hardwood
ii. Floating hardwood
iii. Engineered hardwood
iv. Glue-down wood flooring
v. Carpet (broadloom or tiles)
vi. Vinyl (sheet or tiles)
vii. Ceramic tile

Features Of Omega Double Groove Aluminum Heat Diffuser Plates

  1. High Quality Aluminum Heat Transfer Plates for 1/2" PEX Tubing
  2. High Quality Aluminum Plates for Fast Heat Transfer
  3. Allow 1-2 inch spacing between plates for expansion
  4. 0.016 Thick Aluminum 4.5" wide

Advantage Of Omega Double Groove Aluminum Heat Diffuser Plates

  1. These die-formed aluminum heat plates snap into the grid modules and help conduct heat from the tubing into the floor.
  2. They're also used in staple-up systems to secure PEX tubing to the underside of the sub-floor to maintain contact between the tubing and the sub-floor.
  3. Excellent way to transfer heat when used with either 1/2 in or 5/8 in PEX tubing
  4. Easy to install
  5. Reduces energy cost
  6. Increases comfort
  7. Convenient for use in staple up systems

Applications Of Omega Double Groove Aluminum Heat Diffuser Plates

Under the Sub-floor installation - Between Floor Joist - Engineered Floor Boards - Between plywood installation (Sandwich Installation)

Contact us for product selection. We are glad to help.

CASE

COPYRIGHT © 2020 HWALU

  • OFFICE: OFFICE: No.52, Dongming RD, Zhengzhou City, Henan Province, P.R.CHINA.
  • MAIL: sales@hwalu.com
  • TEL: +86 371 66302886
  • Mobile Phone / Whatsapp: +86 13298118003

Links: Heat Transfer Plates